How to rotate lead groups to stay under invite limits
Split your market into lead groups and rotate which group each campaign points at so outreach stays steady without testing LinkedIn invite limits.
Get startedShort answer
Split your target market into lead groups and rotate which group each campaign points at. LinkedIn does not publish exact invite limits, so the goal is to stay inside whatever limit your account has and keep the pending pool healthy.
Why a single lead group slows you down
A single list makes every campaign compete for the same people. If the list holds your best buyers, the first campaign pulls from the top and leaves the rest waiting. When the account reaches its invite limit, the whole list stalls. You cannot move to a different angle or a different buyer without waiting.
Rotating groups fixes the sequencing problem. You keep several smaller pools and point one campaign at a time at each pool. When one group has had attention, swap to another. The account stays active, and every buyer segment gets a turn.
Group size should match what you can work through in a week or two. A group that is too large hides which segment is replying. A group that is too small runs out before you learn anything.
One giant list
- You hit the account's invite limit on the first batch in your best niche.
- The rest of your market sits untouched for weeks.
- A weak first message reaches every buyer segment before you can fix it.
Rotated groups
- You send a few invites to each group and keep every segment moving.
- You can change the first line for one group without rewriting the whole campaign.
- A slow group does not block the groups that are replying.
How to segment leads for rotation
Segment by something that changes the message. Seniority changes the problem you lead with. Industry changes the example you use. Source changes how warm the lead is. Geography changes the send window. Pick two dimensions at most, then make groups that are easy to name.
The groups do not need to be equal. Put the highest intent leads in a smaller group and give them more attention. Keep a broad group for testing new copy. Keep a separate group for people who commented on competitor posts because those leads have context you can use in the first line.
High intent
- Group
- Commenters on competitor posts
- Source
- High
Core persona
- Group
- Exact job title and industry
- Source
- Medium
Secondary persona
- Group
- Adjacent industries or lower seniority
- Source
- Low
Geographic targets
- Group
- Specific city or region
- Source
- Medium
Set a rotation schedule you can keep
Rotation is a calendar decision, not a campaign rewrite. Decide how long each group stays active. A week per group is easy to track and gives a campaign enough sends to produce replies. A daily swap creates more admin and makes it harder to see which group worked.
Use the same send window for every group so the only thing changing is the audience. If you sell across time zones, build geography into the group and set the window per lead. Do not change the offer and the audience in the same week unless you plan to read the replies closely.
- 1
Create separate lead groups
Build a handful of groups based on the segments you chose. Keep names short enough to scan in a list.
- 2
Pick the first group
Point your active campaign at one group and leave it there for the planned period.
- 3
Swap at the planned time
When the period ends, point the same campaign at the next group. Change the first line if the group has different context.
- 4
Review before the next cycle
Check replies and pending invitations. Drop groups that do not fit. Split groups that are too broad to write for.
Keep the pending invite pool healthy
Pending invitations are connection requests that have not been accepted or withdrawn. LinkedIn lets you send new requests only while that pool has room. If the pool fills, new invites stop even when you have not sent any today. The pool matters as much as the daily limit.
Check pending invitations before you add a new group. If the pool is high, withdraw requests that have been sitting for a couple of weeks. Then wait for the pool to come down before you start a new rotation. Do not solve a full pool by opening another campaign pointed at the same people.
Acceptance rate is a signal. If one group accepts well, keep it in rotation. If another group sits unanswered, change the targeting or the note before you send more.
Withdraw invitations that have sat unanswered for a couple of weeks before you add a new group. A full pending pool stops new requests no matter how many you sent today.
Adjust the message when you swap groups
The audience change should show up in the first line. A commenter on a competitor post should get a note about that post. A VP in a new industry should get a note about the problem that industry has. If every group gets the same note, rotation only changes the names, and the replies will not tell you much.
Keep the campaign goal and tone the same. Change the proof, the example, or the reason you reached out. Write the note in plain language and keep it short. The reader should know why they got the request without opening your profile.
The swap does not need a new campaign for every group. Point the same campaign at a new group, edit the note, and keep the follow-ups aligned with the new context.
Example
- You
Hi Sarah, saw your comment on the Acme post about manual tracking. Would love to connect.
- Prospect
Thanks for reaching out. I'm always looking to meet others in the space.
- You
Glad to connect. Are you still using the manual tracking method you mentioned?
Doing this with Kinlead
Kinlead keeps leads in lead groups, and any campaign can point at any group. You can build a group from a search, from your website, from a CSV of LinkedIn profile URLs, or from the Steal Customers agent. Leads are scored on a 0 to 100 scale against the customer you describe, and leads below the fit line are not kept.
The Steal Customers agent watches competitor company pages and optional founder or employee profiles, reads comments on recent posts, and turns commenters who look like buyers into leads. Each lead keeps the post URL, what the post was about, and what they commented, so the first line of the note has real context. For the scoring side, see lead groups and scoring.
Kinlead sends at most one action every 5 minutes inside the daily invite and message limits you set and inside your send window. It withdraws stale pending invitations automatically, and Settings shows pending invitations and acceptance rate with warnings. When LinkedIn pushes back on an account, Kinlead pauses invites on that account and emails you.
Frequently asked questions
Related
Get started with Kinlead
Prefer markdown? How to rotate lead groups to stay under invite limits.md